Reef Builder™ raises carbonate alkalinity (KH) without immediately impacting on pH. With long term use there will be a tendency to stabilize at pH 8.3. Used as directed, Reef Builder™ will not deplete calcium, magnesium, or strontium which usually tend to precipitate with increasing alkalinity. Reef Builder™ and Reef Buffer™ may be used together. Use Reef Builder™ to raise carbonate alkalinity without affecting pH. Use Reef Buffer™ to raise carbonate alkalinity and pH. Reef alkalinity should be maintained at 3–5 meq/L (8–14 dKH). Alkalinity should not be allowed to fall below 2 meq/L.
Directions
Beginner
Use 3 g (1/2 level teaspoon) per 150 L (40 US gallons) twice a week. Dissolve in at least 250 mL (1 cup) of freshwater. Check alkalinity every 2 weeks and adjust amount or frequency accordingly. For precise dosing, use the Seachem Digital Spoon Scale.
Advanced
Check alkalinity (use MultiTest™ Marine pH & Alkalinity to test alkalinity levels), then follow addition regimen above until alkalinity is adjusted to 3-6 meq/L (8-17 dKH). Each 3 g/150 L will raise alkalinity by about 0.25 meq/L. Quantity or frequency can be adjusted, but do not exceed 12 g/150 L per day. Thereafter, use as required to maintain alkalinity.
Check alkalinity (use MultiTest™ Marine pH & Alkalinity to test alkalinity levels), then follow addition regimen above until alkalinity is adjusted to 3-6 meq/L (8-17 dKH). Each 3 g/150 L will raise alkalinity by about 0.25 meq/L. Quantity or frequency can be adjusted, but do not exceed 12 g/150 L per day. Thereafter, use as required to maintain alkalinity.
Expert
After determining the alkalinity consumption rate, set up a continuous drip system. Use the following formula (or skip the math and use our Dosage Calculator) to determine how much to add to your top–off water: m=0.08va (m=grams to add to top off water, v=volume of tank in liters, a=amount to raise alkalinity in meq/L). For example, if you want to raise your alkalinity by 1 meq/L in a 200 liter tank, then you would add 0.08x200x1=16 g into the top–off water. [For reference: 1 gallon=3.8 liters, 6 g=1 teaspoon].
After determining the alkalinity consumption rate, set up a continuous drip system. Use the following formula (or skip the math and use our Dosage Calculator) to determine how much to add to your top–off water: m=0.08va (m=grams to add to top off water, v=volume of tank in liters, a=amount to raise alkalinity in meq/L). For example, if you want to raise your alkalinity by 1 meq/L in a 200 liter tank, then you would add 0.08x200x1=16 g into the top–off water. [For reference: 1 gallon=3.8 liters, 6 g=1 teaspoon].
DO NOT OVERDOSE: Excess alkalinity may enhance the loss of calcium, magnesium, and strontium. Do not directly mix with any calcium, magnesium, or strontium supplement. Best if calcium & carbonate additives are added on alternate days or at least 30 minutes apart.
FAQ
What is the difference between Reef Builder™ and Reef Buffer™?
A: While both products affect pH and alkalinity, Reef Buffer's™ primary function is affecting pH, while Reef Builder's™ primary function is affecting alkalinity.
A: While both products affect pH and alkalinity, Reef Buffer's™ primary function is affecting pH, while Reef Builder's™ primary function is affecting alkalinity.
When pH is the primary concern, use Reef Buffer™. When pH is not an issue, use Reef Builder™ to adjust alkalinity.
When I dissolve Reef Builder™ at the prescribed 4 tspn per gallon in RO water the resulting solution is cloudy and does not clear upon standing. Also sometimes I find some of the material is very stubborn to dissolve. Is this normal?
A: When dissolving at the prescribed concentrations it is normal for the solution to be somewhat cloudy. Add Reef Builder™ to your RO water, and stir it for a few minutes or let it stand about 10 minutes, then add it to your tank. It will dissolve rapidly at this point. Pre-dissolving Reef Builder™ is recommended mainly as a more gentle delivery method (as opposed to just putting the dry product directly in the tank) not as something you would dose with (in which case you would want it all dissolved). It is also normal for small amounts of the material to not be dissolved if you let the RO or DI water and Reef Builder™ solution sit overnight... small amounts of calcium carbonate can form sometimes within the bottle, and it is this material (chalk) which is very insoluble. It will eventually dissolve in the tank however since the amounts are very small and the volume of the tank is many times greater than the 1 gallon of RO or DI water.
A: When dissolving at the prescribed concentrations it is normal for the solution to be somewhat cloudy. Add Reef Builder™ to your RO water, and stir it for a few minutes or let it stand about 10 minutes, then add it to your tank. It will dissolve rapidly at this point. Pre-dissolving Reef Builder™ is recommended mainly as a more gentle delivery method (as opposed to just putting the dry product directly in the tank) not as something you would dose with (in which case you would want it all dissolved). It is also normal for small amounts of the material to not be dissolved if you let the RO or DI water and Reef Builder™ solution sit overnight... small amounts of calcium carbonate can form sometimes within the bottle, and it is this material (chalk) which is very insoluble. It will eventually dissolve in the tank however since the amounts are very small and the volume of the tank is many times greater than the 1 gallon of RO or DI water.
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.